IH PARTS AMERICA
Click Here!

Go Back   IH PARTS AMERICA > Tech Forums > Ignition Tech
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read Photo Gallery Store Home

Reply
 
LinkBack Thread Tools Display Modes
Old 07-28-2011, 03:18 PM   #1 (permalink)
Member
 
Join Date: May 2011
Member Number: 3420
Location: Mesa AZ
Posts: 73
Default What Distributor cap and rotor needed for fuel injection kit?

Just got the fuel injection kit for my Scout II 345 but there is no distributor cap or rotor in the box. What Distributor cap and rotor is needed for fuel injection kit?

And while I am asking, what is the best set of ignition wires for the same?

Thanks in advance
IceFyre13th is offline   Reply With Quote
Old 07-28-2011, 05:32 PM   #2 (permalink)
Senior Member
 
Craig's Avatar
 
Join Date: Jan 2007
Member Number: 5
Location: Sacramento
Posts: 1,194
Default Re: What Distributor cap and rotor needed for fuel injection kit?

did you buy it from an IH vender? if so, contact them.

For the DIY crowed there are 2 ways to. check Bills FAQ and look for Mopar conversion of your stock Holly dissy.

Or there is a guy in Idaho that will marry a GM and IH dissy if you send him money and dissy's
__________________
Craig is offline   Reply With Quote
Old 07-29-2011, 09:38 AM   #3 (permalink)
Member
 
Join Date: May 2011
Member Number: 3420
Location: Mesa AZ
Posts: 73
Default Re: What Distributor cap and rotor needed for fuel injection kit?

Complete TBI Fuel Injection System for your IH - International Scout Parts

That is the kit I have, notice in the picture the cap is on the distributor, my kit dose not have this part or the rotor in the box.

So I either have to buy one, or I got shorted and one has to be sent to me.

I posted the question here as IHOnlyNorths contact page said to post here as they get too many E-mails.
IceFyre13th is offline   Reply With Quote
Old 07-29-2011, 01:01 PM   #4 (permalink)
Senior Member
 
Craig's Avatar
 
Join Date: Jan 2007
Member Number: 5
Location: Sacramento
Posts: 1,194
Default Re: What Distributor cap and rotor needed for fuel injection kit?

You would have to post a pic in this thread for me to see it, as it laying down with a top in the back of the pic.

It looks like a GM top. Note: the 1980 Scout and the GM cap uses a male cap vs a female cap on the dissy.
Also the GM cap stem height of the male plastic part is about 1/4" shorter then a 1980 IH cap. So I found the spark plug wires would not slip on tight. I trimmed about 1/8 of the spark plug boot off to get them to fit tight.

I did not get the setup you have, but Jeff makes all his stuff plug and play and you might not need to doing anything.

A quick call to Jeff would clear all of this up.

my dissy looks like this



I used stock 1980 wires




This might help you too.
__________________

Last edited by Craig; 07-29-2011 at 01:11 PM..
Craig is offline   Reply With Quote
Old 08-01-2011, 01:38 PM   #5 (permalink)
Member
 
Join Date: May 2011
Member Number: 3420
Location: Mesa AZ
Posts: 73
Default Re: What Distributor cap and rotor needed for fuel injection kit?

Thanks for the information, but I still need to find out what I have.

Guess I will have to call Jeff............
IceFyre13th is offline   Reply With Quote
Old 08-02-2011, 10:21 AM   #6 (permalink)
Member
 
Join Date: May 2011
Member Number: 3420
Location: Mesa AZ
Posts: 73
Default Re: What Distributor cap and rotor needed for fuel injection kit?

Talked to Jeff last night, the new AFI kit dose not include the cap and rotor for the distributor any more. But the parts needed are for a 1975 Scout II Holly distributor.

Thanks for the help again.
IceFyre13th is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -8. The time now is 05:45 PM.